3D Printing -

3D Printing – „Lost Heresy Miniatures“ – Vulgorn Guards

„Lost Heresy Miniatures“ WIPs – Three of the Vulgorn Guards currently being progressed
All of these models were created using „Elegoo“ Water Washable Resin on a Mars 3 Pro 3D Printer and are available as STL (Standard Triangle Language) files from „Lost Heresy Miniatures“ on „MyMiniFactory“. The rotund extra-terrestrials are part of an eight-figure collection, whose sculpts have clearly been heavily-inspired by the Vogons as seen in Garth Jennings‘ 2005 movie „The Hitchhiker’s Guide to the Galaxy“.

I’ve actually had a bit of an ‚on-off‘ relationship supporting this creator on Tribe in the past, as I’ve found their (predominantly science fiction) range to be a bit smaller than most modern-day models – probably being 25mm as opposed to today’s 28mm scale. Happily however, I’m a bit more knowledgeable about the data preparation software programme „Chitubox“ Basic than I used to be, so these days tend to upscale most of the smaller STLs I print out by 108.41% (measured using the Colonist Marine Cyborg Hero E-900 Exterminator figure by „Papsikels Miniatures“ as the new eye-line height – also known as ‚Arnie Scale‘).

„Lost Heresy Miniatures“ WIPs – Three more Vulgorn Guards which have been primed, shaded and dry-brushed
This did admittedly make the aliens somewhat larger than a normal-sized human. But having viewed several photographs of Prostetnic Vogon Jeltz, it’s clear that in the film (at least) the intergalactic civil servants are a lot bigger than mere Earthlings anyway. Regardless, as soon as I saw the set I simply had to get some printed out, especially as they’re appearance was something of a welcome surprise – considering that up until this point recently „Lost Heresy Miniatures“ had been focusing upon producing a splendid range of characterful Napoleonic Russians for „The Silver Bayonet“ rule-set by „Osprey Games“.

What I was not prepared for though, was just how difficult it would prove to print out some useable models to paint – and much of this frustration was unfortunately down to me as opposed to anything else, though it took quite a few failed attempts over an entire week before I realised what was happening. To begin with I thought that my upscaling had caused the pre-supports to become unstable, as several appeared to break away from the print mid-way through the production process.

The Vulgorn Guards pre-supported, then supported by „Chitubox“, and finally with my (Large) supports
I’m always a bit sceptical of pre-supported files at the best of times, so subsequently tried adding some additional Large supports to the sculpts where-ever I felt there was a weak area. This helped produce a couple of working figures, as well as two which required some Green-Stuff repair work to make right. But was still largely creating failures. Indeed, having initially envisaged a plate of five nicely printed Vulgorn Guards every time I was now almost down to trying just a single miniature in case there were any resin flow issues occurring with an over packed plate.

I even tried completely doing my own supports and repositioning the models at a 35 degree angle – my failsafe placement. But even this caused repeated fails. Fortunately, I then spotted that the FEP (Fluorinated Ethylene Propylene) was actually touching the LCD (Liquid Crystal Display) mono 4K screen by the end of the printing process – indicating that the FEP’s tension was no longer as taut as it should be – not a surprise considering that I last changed it almost a year ago. A quick swap of the resin bed for a factory-made one, and things finally started to work…

Powered by WPeMatico

Dieser Artikel stammt von einer der angeschlossenen Quellen. Bitte honoriere die Arbeit der Autoren indem du ihren Webseite besuchst.

Artikelquelle besuchen
Autor: / Fantorical

Anzeige:
Eis.de